Fixing “Atomizer Short” and Other Vape Mod Errors

The key advantage of owning a vape mod is its versatility. With devices like the Innokin Sensis or the Innokin Kroma 217, you gain the ability to customize your vaping experience according to your preferences. You’re free to attach any vape tank of your choice and adjust the settings to achieve the perfect balance of warmth and flavor.

However, one possible downside to owning a vape mod is that the numerous hardware and settings combinations might lead to configurations that could malfunction. This might result in an error message such as “Atomizer Short” appearing on your vape mod.

While every Innokin vape mod comes with a printed manual that offers troubleshooting tips for the error messages you might encounter, a more extensive troubleshooting guide detailing common vape mod issues can often be even more beneficial. This is the resource you have found here. In this guide, we’ll share tips to assist you in resolving any error message that appears on your vape mod.

Essential Tips for Smooth Vaping

We will kick off this guide with some essential advice that can help ensure a smooth and enjoyable vaping journey, no matter the device type you are using. These tips are relevant for all vape mods.

• Always keep your vape tank topped up. A low e-liquid level will hinder the coil’s wick from absorbing e-liquid effectively, leading to a dry wick that can burn and negatively affect flavor.
• Exercise caution while disassembling your vape tank for coil replacement. Misaligned components can lead to leaking or trigger error messages. Encountering an error like “Atomizer Short” after refilling your tank would be unfortunate, as it results in wasted e-liquid.
• When installing a new coil, start with your vape mod set to low wattage, gradually increasing until you reach your preferred flavor intensity. Vaping at excessive wattage on a new coil risks burning the wick prematurely.
• When charging your vape mod, always connect it through a computer’s USB port unless it uses a removable battery and you choose to use a quality external charger. Avoid fast-charging wall adapters for mobile devices, as they are incompatible with vape mods and may overheat your device.
• Ensure you use an undamaged, high-amperage battery for your vape mod. Batteries showing any signs of physical wear should be recycled. In cases where your vape mod uses two batteries, they should be identical and of the same age. Always charge and use the battery pair together.

Resolving an “Atomizer Short” or “Coil Short” Error Message

When your vape mod displays the “Atomizer Short” error message, it indicates that while the device recognizes the atomizer coil, the circuit is short or incomplete. A short circuit could pose a safety issue for the battery, which is why your vape mod will alert you with an error message when you attempt to use it. Here’s how to troubleshoot this issue.

• If using a rebuildable atomizer, check the coil’s resistance using an external tester if available. Often, the coil might be improperly configured; for instance, one of the leads could be contacting the outer casing of the atomizer.
• If you have a vape tank with pre-built coils, consider disassembling and reassembling the tank to ensure all parts are securely fitted and not cross-threaded. Also, check that the center pins in both the tank and vape mod threading are clear. If the “Atomizer Short” issue persists, replace the coil.

“`html

Resolving a “Low Battery” or “Low Volt” Error Message

When your vape mod shows a “Low Battery” or “Low Volt” error message, it indicates that the voltage of the battery is insufficient for normal operation, signaling that it’s time for a battery recharge. If this warning persists after charging, ensure that you are charging the device by connecting it to your computer’s USB port. Allow the screen to indicate that the charging cycle has completed before attempting to use it again.

Should the “Low Battery” message remain visible after charging, it might suggest that the battery has deteriorated to the point it can no longer retain a usable charge. If the battery is removable, recycle the old battery and replace it with a new one. If the battery is non-removable, it may be necessary to consider replacing the entire device. Remember, the Innokin warranty protects against defects for the first 90 days post-purchase, and you can qualify for an extended warranty of 180 days by registering your product with Innokin at the time of purchase.

Resolving a “Check Coil” Error Message

When the “Check Coil” error message appears on your vape mod, this indicates that while the mod recognizes the coil is connected, the coil’s resistance falls outside the acceptable range for the device or it isn’t establishing a proper electrical connection. You should refer to the steps provided earlier under the “Atomizer Short” issue. Ensure that the connections located on the base of the tank as well as on the vape mod are clean and devoid of dust or spilled e-liquid. Try disassembling and reassembling the tank. If the error message persists, you will need to replace the coil.

Resolving a “Vape Cutoff” or “Time Out” Error Message

If the error “Vape Cutoff” or “Time Out” appears on your vape mod, this indicates you are taking excessively long puffs that exceed the device’s built-in puff length limit. This limiter is designed to help prevent overheating during extended vaping sessions and provides a safety measure against the fire button being unintentionally pressed while the device is being moved or stored.

In certain advanced Innokin vape mods, like the Innokin Kroma 217 and Innokin Sensis EZ, there is an option to adjust the puff limiter to fit your preferences. To change the maximum puff length, access the mod’s main menu and find the “Settings” section. Within this menu, select the “Cutoff” option to customize the puff length between 3 to 18 seconds. Always take care when vaping with prolonged puffs, as a dried out wick can lead to burning, which will adversely affect the flavor of your coil.

Resolving an “Overheat” or “High Temp” Error Message

Your Innokin vape mod is equipped with a built-in temperature sensor on the circuit board, continuously monitoring the internal temperature to prevent overheating. An “Overheat” or “High Temp” error message signifies that the internal temperature has surpassed 90 degrees Celsius, potentially damaging the device’s components if vaping continues.

A vape mod usually overheats due to heavy use, commonly referred to as “chain vaping,” or if used in an excessively hot environment, such as direct sunlight. Given that a vaping device generates considerable heat during use, it is crucial to avoid operating a vape mod in high temperatures or direct sunlight. Relocate your device to a cooler place and allow it to rest for a while before attempting to vape again.

Always ensure that your vape mod is stored in a cool area when not in use. If you’re outdoors and need to set your device down, opt for a shaded spot. Avoid leaving your vape mod inside a parked car.

“““html

Resolving a “Low Res” Error Message

The error message “Low Res” means that your vape mod has recognized the atomizer coil that’s been installed, yet the resistance of that coil falls below what the mod can support. If utilizing a third-party tank, check your vape mod’s user manual to find out the minimum resistance it can handle. For instance, the Innokin Sensis EZ has a minimum supported resistance of 0.2 ohm, whereas the Innokin Kroma 217 is capable of handling a coil resistance as low as 0.05 ohm.

If you think that your vape mod ought to support the coil you have attached, adhere to the instructions given previously regarding the “Atomizer Short” error message. Clean any debris from the threading on both your tank and mod. Ensure that your tank is properly assembled, with all parts tightly screwed in and free from cross-threading. Should the error message persist, the coil might have a defect from manufacturing, leading to the need for a replacement.